AdapterID 5039h

AdapterName  "Flatbed Scanner Interface"

NumBytes 4

NamedItem
	Prompt	"Adapter I/O Location"
	  Choice "Address 02E8"  pos[1]=XXXXX000b  io 02e8h-02efh
	  Choice "Address 12E8"  pos[1]=XXXXX001b  io 12e8h-12efh
	  Choice "Address 22E8"  pos[1]=XXXXX010b  io 22e8h-22efh
	  Choice "Address 32E8"  pos[1]=XXXXX011b  io 32e8h-32efh
	  Choice "Address 42E8"  pos[1]=XXXXX100b  io 42e8h-42efh
	  Choice "Address 52E8"  pos[1]=XXXXX101b  io 52e8h-52efh
	  Choice "Address 62E8"  pos[1]=XXXXX110b  io 62e8h-62efh
	  Choice "Address 72E8"  pos[1]=XXXXX111b  io 72e8h-72efh
	Help
	"To configure this adapter you must choose the I/O port address
	 that the adapter will respond to.  There are 8 I/O address blocks
	 that can be selected.	Under normal circumstances, select <Address
	 02E8>."

NamedItem
	Prompt	"Interrupt Level"
	  Choice  "Level 10"  pos[2]=XXXXX001b  int 10
	  Choice  "Level 9"   pos[2]=XXXXX000b  int 9
	  Choice  "Level 11"  pos[2]=XXXXX010b  int 11
	  Choice  "Level 12"  pos[2]=XXXXX011b  int 12
	  Choice  "Level 13"  pos[2]=XXXXX100b  int 14
	  Choice  "Level 14"  pos[2]=XXXXX101b  int 15
	  Choice  "Level 3"   pos[2]=XXXXX110b  int 3
	  Choice  "Level 4"   pos[2]=XXXXX111b  int 4
	Help
	"Interrupt level.  This selects the interrupt level that the adapter
	 will generate.  The choices are listed in the order of priority with
	 level 9 being the highest.  Under normal circumstances, select
	 <Level 10>."

NamedItem
	Prompt	"DMA Arbitration Level"
	  Choice  "Level 5"   pos[3]=XXXX0101b  arb 5
	  Choice  "Level 0"   pos[3]=XXXX0000b  arb 0
	  Choice  "Level 1"   pos[3]=XXXX0001b  arb 1
	  Choice  "Level 2"   pos[3]=XXXX0010b  arb 2
	  Choice  "Level 3"   pos[3]=XXXX0011b  arb 3
	  Choice  "Level 4"   pos[3]=XXXX0100b  arb 4
	  Choice  "Level 6"   pos[3]=XXXX0110b  arb 6
	  Choice  "Level 7"   pos[3]=XXXX0111b  arb 7
	  Choice  "Level 8"   pos[3]=XXXX1000b  arb 8
	  Choice  "Level 9"   pos[3]=XXXX1001b  arb 9
	  Choice  "Level 10"  pos[3]=XXXX1010b  arb 10
	  Choice  "Level 11"  pos[3]=XXXX1011b  arb 11
	  Choice  "Level 12"  pos[3]=XXXX1100b  arb 12
	  Choice  "Level 13"  pos[3]=XXXX1101b  arb 13
	  Choice  "Level 14"  pos[3]=XXXX1110b  arb 14
	Help
	"This selects the DMA channel that the adapter will use to transfer
	 data.	Under normal circumstances, select <Level 5>."

NamedItem
	Prompt	"Interrupt On/Off"
	  Choice  "Off"
	    pos[2]=XXXX0XXXb
	  Choice  "On"
	    pos[2]=XXXX1XXXb
	Help
	"Interrupt enable bit.  When set to 'On' this bit allows the adapter
	 to control interrupt enable (IEN) through it's control register.
	 This is a safeguard against any software drivers that may
	 inadvertently enable interrupts on the adapter when it wasn't
	 supposed to.  Under normal circumstances, select <Off>. "


NamedItem
	Prompt	"Fairness On/Off"
	  Choice  "On"
	    pos[3]=X1XXXXXXb
	  Choice  "Off"
	    pos[3]=X0XXXXXXb
	Help
	"Bus Arbitration Fairness.  This controls whether the adapter will
	 release control of the bus when it has been using it exclusively.
	 Under normal circumstances, select <On>."

NamedItem
	Prompt	"Card Enable On/Off"
	  Choice  "On"   pos[0]=XXXXXXX1b
	  Choice  "Off"  pos[0]=XXXXXXX0b
	Help
	"Card enable (CDEN) bit.  This controls whether the board can be
	 accessed through I/O port addresses selected in the Adapter I/O
	 Location section.  Under normal circumstances, select <On>."