AdapterID 503Ah

AdapterName  "Model 115 Scanner Interface"

NumBytes 3

NamedItem
	Prompt	"Adapter Version"
	  Choice "Rev C"   pos[0]=01XXXXXXb
	Help
	"Bits 6 & 7 identify the Model 115 board revision level that
	 this adf file supports. It is set for Rev C boards and up."

NamedItem
	Prompt	"Adapter I/O Location"
	  Choice "Address 02E0"  pos[2]=1110XXXXb  io 02E0h-02E7h
	  Choice "Address 0200"  pos[2]=0000XXXXb  io 0200h-0207h
	  Choice "Address 0210"  pos[2]=0001XXXXb  io 0210h-0217h
	  Choice "Address 0220"  pos[2]=0010XXXXb  io 0220h-0227h
	  Choice "Address 0230"  pos[2]=0011XXXXb  io 0230h-0237h
	  Choice "Address 0240"  pos[2]=0100XXXXb  io 0240h-0247h
	  Choice "Address 0250"  pos[2]=0101XXXXb  io 0250h-0257h
	  Choice "Address 0260"  pos[2]=0110XXXXb  io 0260h-0267h
	  Choice "Address 0270"  pos[2]=0111XXXXb  io 0270h-0277h
	  Choice "Address 0280"  pos[2]=1000XXXXb  io 0280h-0287h
	  Choice "Address 0290"  pos[2]=1001XXXXb  io 0290h-0297h
	  Choice "Address 02A0"  pos[2]=1010XXXXb  io 02A0h-02A7h
	  Choice "Address 02B0"  pos[2]=1011XXXXb  io 02B0h-02B7h
	  Choice "Address 02C0"  pos[2]=1100XXXXb  io 02C0h-02C7h
	  Choice "Address 02D0"  pos[2]=1101XXXXb  io 02D0h-02D7h
	  Choice "Address 02F0"  pos[2]=1111XXXXb  io 02F0h-02F7h
	Help
	"To configure this adapter you must choose the I/O port address
	 that the adapter will respond to.  There are 16 I/O address blocks
	 that can be selected.	Under normal circumstances, select <Address
	 02E0>."

NamedItem
	Prompt	"Interrupt Level"
	  Choice  "Level 10"  pos[2]=XXXXX001b  int 10
	  Choice  "Level 9"   pos[2]=XXXXX000b  int 9
	  Choice  "Level 11"  pos[2]=XXXXX010b  int 11
	  Choice  "Level 12"  pos[2]=XXXXX011b  int 12
	  Choice  "Level 13"  pos[2]=XXXXX100b  int 14
	  Choice  "Level 14"  pos[2]=XXXXX101b  int 15
	  Choice  "Level 3"   pos[2]=XXXXX110b  int 3
	  Choice  "Level 4"   pos[2]=XXXXX111b  int 4
	Help
	"Interrupt level.  This selects the interrupt level that the adapter
	 will generate.  The choices are listed in the order of priority with
	 level 9 being the highest.  Under normal circumstances, select
	 <Level 10>."

NamedItem
	Prompt	"DMA Arbitration Level"
	  Choice  "Level 5"   pos[3]=XXXX0101b  arb 5
	  Choice  "Level 0"   pos[3]=XXXX0000b  arb 0
	  Choice  "Level 1"   pos[3]=XXXX0001b  arb 1
	  Choice  "Level 2"   pos[3]=XXXX0010b  arb 2
	  Choice  "Level 3"   pos[3]=XXXX0011b  arb 3
	  Choice  "Level 4"   pos[3]=XXXX0100b  arb 4
	  Choice  "Level 6"   pos[3]=XXXX0110b  arb 6
	  Choice  "Level 7"   pos[3]=XXXX0111b  arb 7
	  Choice  "Level 8"   pos[3]=XXXX1000b  arb 8
	  Choice  "Level 9"   pos[3]=XXXX1001b  arb 9
	  Choice  "Level 10"  pos[3]=XXXX1010b  arb 10
	  Choice  "Level 11"  pos[3]=XXXX1011b  arb 11
	  Choice  "Level 12"  pos[3]=XXXX1100b  arb 12
	  Choice  "Level 13"  pos[3]=XXXX1101b  arb 13
	  Choice  "Level 14"  pos[3]=XXXX1110b  arb 14
	Help
	"This selects the DMA channel that the adapter will use to transfer
	 data.	Under normal circumstances, select <Level 5>."

NamedItem
	Prompt	"Interrupt On/Off"
	  Choice  "Off"
	    pos[2]=XXXX0XXXb
	  Choice  "On"
	    pos[2]=XXXX1XXXb
	Help
	"Interrupt enable bit.  When set to 'On' this bit allows the adapter
	 to control interrupt enable (IEN) through it's control register.
	 This is a safeguard against any software drivers that may
	 inadvertently enable interrupts on the adapter when it wasn't
	 supposed to.  Under normal circumstances, select <Off>. "


NamedItem
	Prompt	"Fairness On/Off"
	  Choice  "On"
	    pos[3]=X1XXXXXXb
	  Choice  "Off"
	    pos[3]=X0XXXXXXb
	Help
	"Bus Arbitration Fairness.  This controls whether the adapter will
	 release control of the bus when it has been using it exclusively.
	 Under normal circumstances, select <On>."

NamedItem
	Prompt	"Card Enable On/Off"
	  Choice  "On"   pos[0]=XXXXXXX1b
	  Choice  "Off"  pos[0]=XXXXXXX0b
	Help
	"Card enable (CDEN) bit.  This controls whether the board can be
	 accessed through I/O port addresses selected in the Adapter I/O
	 Location section.  Under normal circumstances, select <On>."