AdapterID 56EAh

AdapterName  "Asante EtherPaC 2100+NT MCA card"

NumBytes 2


NamedItem
        Prompt  "Remote Boot"
          choice " Enable "
            pos[0]=XXXXXX01b
          choice " Disable "
            pos[0]=XXXXXX11b
        Help
         "Select Enable if you install a remote boot ROM on
         your network interface card and intend to remote boot from
         a server;select Disable if you intend to boot from your own
         computer."

Nameditem
        Prompt "IRQ Line"
          choice " 3 "
            pos[0]=XXX000XXb
            int 3
          choice " 4 "
            pos[0]=XXX001XXb
            int 4
          choice " 5 "
            pos[0]=XXX010XXb
            int 5
          choice " 9 "
            pos[0]=XXX011XXb
            int 9
          choice " 10 "
            pos[0]=XXX100XXb
            int 10
          choice " 11 "
            pos[0]=XXX101XXb
            int 11
          choice " 14 "
            pos[0]=XXX110XXb
            int 14
          choice " 15 "
            pos[0]=XXX111XXb
            int 15
     Help
        "This specifies the Interrupt Request Line used by your network
        interface card when it needs a service from the host CPU. There
        are eight IRQ lines that you can select from. Under the normal
        circumstance, use the IRQ line selected for you when you ran the
        Auto-Configuration."

Nameditem prompt "Base I/O address"
          choice " 300h "
            pos[0]=X00XXXXXb
            io 0300h-031Fh
          choice " 320h "
            pos[0]=X01XXXXXb
            io 0320h-033fh
          choice " 340h "
            pos[0]=X10XXXXXb
            io 0340h-035Fh
          choice " 360h "
            pos[0]=X11XXXXXb
            io 0360h-037Fh
        Help
           "This specifies the beginning address of memory segment used as the
           I/O port for communication between your network interface card and
           the PS/2 host. There are four base I/O addresses that you can select
           from. Under the normal circumstance, use the base I/O address
           selected for you when you run the Auto-Configuration."

Nameditem
        Prompt  "ROM Address Range"
          choice " 16K \ C8000 - CBFFF"
            pos[1]=XXX10010b
            mem 0c8000h-0cbfffh
          choice " 16K \ CC000 - CFFFF"
            pos[1]=XXX10011b
            mem 0cc000h-0cffffh
          choice " 16K \ D0000 - D3FFF"
            pos[1]=XXX10100b
            mem 0d0000h-0d3fffh
          choice " 16K \ D4000 - D7FFF"
            pos[1]=XXX10101b
            mem 0d4000h-0d7fffh
          choice " 16K \ D8000 - DBFFF"
            pos[1]=XXX10110b
            mem 0d8000h-0dbfffh
          choice " 16K \ DC000 - DFFFF"
            pos[1]=XXX10111b
            mem 0dc000h-0dffffh
          choice "  8K \ C8000 - C9FFF"
            pos[1]=XXX11010b
            mem 0c8000h-0c9fffh
          choice "  8K \ CC000 - CDFFF"
            pos[1]=XXX11011b
            mem 0cc000h-0cdfffh
          choice "  8K \ D0000 - D1FFF"
            pos[1]=XXX11100b
            mem 0d0000h-0d1fffh
          choice "  8K \ D4000 - D5FFF"
            pos[1]=XXX11101b
            mem 0d4000h-0d5fffh
          choice "  8K \ D8000 - D9FFF"
            pos[1]=XXX11110b
            mem 0d8000h-0d9fffh
          choice "  8K \ DC000 - DDFFF"
            pos[1]=XXX11111b
            mem 0dc000h-0dDfffh
          choice " 32K \ C8000 - CFFFF"
            pos[1]=XXX01010b
            mem 0c8000h-0cffffh
          choice " 32K \ CC000 - D3FFF"
            pos[1]=XXX01011b
            mem 0cc000h-0d3fffh
          choice " 32K \ D0000 - D7FFF"
            pos[1]=XXX01100b
            mem 0d0000h-0d7fffh
          choice " 32K \ D4000 - DBFFF"
            pos[1]=XXX01101b
            mem 0d4000h-0dbfffh
          choice " 32K \ D8000 - DFFFF"
            pos[1]=XXX01110b
            mem 0d8000h-0dffffh
          choice " 32K \ DC000 - E3FFF"
            pos[1]=XXX01111b
            mem 0dc000h-0e3fffh

        Help
           "This specifies the beginning address of an 8KB or 16KB or 32KB
           memory segment used by your network interface card's remote boot ROM.
           There are six base memory addresses that you can select from.
           Under the normal circumstance, use the base memory address
           selected for you when you ran the Auto-configuration."

Nameditem
        Prompt "Media type"
          choice " Coaxial cable"
            pos[1]=X00XXXXXb
          choice " Twisted_pair"
            pos[1]=X01XXXXXb
        Help
           "This specifies the Tranceiver media type."