AdapterId 08099h

AdapterName "#9GX Microchannel Graphics Adapter"

NumBytes 3

NamedItem

Prompt	"Enable/Disable Adapter"

Choice " Adapter Enabled "   pos[0]=XXXXXXX1b
Choice " Adapter Disabled "  pos[0]=XXXXXXX0b

Help
"This allows the adapter to be enabled or disabled
without removing it from the system. When enabled
the adapter will respond to all accesses made to it.
If disabled the adapter will not respond to any
memory or I/O operations. Setup must be run again
to enable the adapter."

NamedItem

Prompt	"Memory Host Interface Address"

Choice " 0C:F000 to 0C:FFFF "
 pos[1]=1111XXXXb pos[2]=00001100b mem 0CF000h-0CFFFFh
Choice " 0C:8000 to 0C:8FFF "
 pos[1]=1000XXXXb pos[2]=00001100b mem 0C8000h-0C8FFFh
Choice " 0C:C000 to 0C:CFFF "
 pos[1]=1100XXXXb pos[2]=00001100b mem 0CC000h-0CCFFFh
Choice " 0D:4000 to 0D:4FFF "
 pos[1]=0100XXXXb pos[2]=00001101b mem 0D4000h-0D4FFFh
Choice " 0D:8000 to 0D:8FFF "
 pos[1]=1000XXXXb pos[2]=00001101b mem 0D8000h-0D8FFFh
Choice " 0D:C000 to 0D:CFFF "
 pos[1]=1100XXXXb pos[2]=00001101b mem 0DC000h-0DCFFFh

Help
"This is used to select the Memory HOST INTERFACE ADDRESS.
Select an address that will not conflict with
other installed adapters."

NamedItem

Prompt	"I/O Host Interface Address"

Choice " 0280 to 0287 "   pos[1]=XXXXXX00b io 0280h-0287h
Choice " 0288 to 028F "   pos[1]=XXXXXX01b io 0288h-028fh
Choice " 0290 to 0297 "   pos[1]=XXXXXX10b io 0290h-0297h
Choice " 0298 to 029F "   pos[1]=XXXXXX11b io 0298h-029fh

Help
"This is used to set the I/O HOST INTERFACE ADDRESS."

NamedItem

Prompt "Device Class"

Choice " 120  1024x768x8 " pos[0]=X00000XXb
Choice " 121  1024x768x4 " pos[0]=X00100XXb
Choice " 122  1024x768x2 " pos[0]=X01000XXb
Choice " 123  1024x768x1 " pos[0]=X01100XXb
Choice " 124  640x480x8 "  pos[0]=X10000XXb
Choice " 125  640x480x4 "  pos[0]=X10100XXb
Choice " 126  640x480x2 "  pos[0]=X11000XXb
Choice " 127  640x480x1 "  pos[0]=X11100XXb
Choice " 130  1280x1024x8 " pos[0]=X00001XXb
Choice " 131  1280x1024x4 " pos[0]=X00101XXb
Choice " 132  1280x1024x2 " pos[0]=X01001XXb
Choice " 133  1280x1024x1 " pos[0]=X01101XXb

Help
"Select the default Device Class for the adapter."

NamedItem

Prompt "VGA Loop Thru"

Choice " Enable Loop Thru "  pos[0]=0XXXXXXXb
Choice " Disable Loop Thru " pos[0]=1XXXXXXXb

Help
"This allows the adapter to emulate VGA. It
can be enabled or disabled."