AdapterId       080F8h

AdapterName     "PG2-1281 Hi-res Graphics Controller - REV 2.0"

NumBytes        2

FixedResources  pos[0]=XXXXX01Xb

;==============================================================================

NamedItem

Prompt  "GENERAL SETUP"

choice  " CENB, ADP1, DUAL, WOFF"   pos[0]=X00X0XX1b
                                    pos[1]=XX1XX1XXb
                                    mem    0C6000h - 0C63FFh  0C7000h - 0C7FFFh

choice  " CENB, ADP1, DUAL, W_ON"   pos[0]=X00X1XX1b
                                    pos[1]=XX1XX1XXb
                                    mem    0C6000h - 0C7FFFh  800000h - 9FFFFFh

choice  " CENB, ADP1, SING, WOFF"   pos[0]=X01X0XX1b
                                    pos[1]=XX0XX0XXb
                                    mem    0C0000h - 0C63FFh  0C7000h - 0C7FFFh

choice  " CENB, ADP1, SING, W_ON"   pos[0]=X01X1XX1b
                                    pos[1]=XX0XX0XXb
                                    mem    0C0000h - 0C7FFFh  800000h - 9FFFFFh

choice  " CENB, ADP2, DUAL, WOFF"   pos[0]=X10X0XX1b
                                    pos[1]=XX1XX1XXb
                                    mem    0C6400h - 0C67FFh  0C7000h - 0C7FFFh

choice  " CENB, ADP2, DUAL, W_ON"   pos[0]=X10X1XX1b
                                    pos[1]=XX1XX1XXb
                                    mem    0C6400h - 0C7FFFh  800000h - 9FFFFFh

choice  " CDIS, ADP1, DUAL, WOFF"   pos[0]=X00X0XX0b
                                    pos[1]=XX1XX1XXb

choice  " CDIS, ADP1, DUAL, W_ON"   pos[0]=X00X1XX0b
                                    pos[1]=XX1XX1XXb
                                    mem    800000h - 9FFFFFh

choice  " CDIS, ADP2, DUAL, WOFF"   pos[0]=X10X0XX0b
                                    pos[1]=XX1XX1XXb

choice  " CDIS, ADP2, DUAL, W_ON"   pos[0]=X10X1XX0b
                                    pos[1]=XX1XX1XXb
                                    mem    800000h - 9FFFFFh

Help    " CDIS : Card DISable, memory used: none.
          CENB : Card ENBble, memory used: 0C7000h - 0C7FFFh.
          ADP1 : ADPpter 1, memory used: 0C6000h - 0C63FFh.
          APD2 : ADPpter 2, memory used: 0C6400h - 0C67FFh.
          DUAL : DUAL screen, memory used: none.
          SING : SINGle screen, memory used: 0C0000h - 0C1FFFh.
          WOFF : 2 Meg Window OFF, memory used: none.
          W_ON : 2 Meg Window ON, memory used: 0800000h - 09FFFFFh.

          NOTE : Only one PG2-1281 must have the CENB configuration,
                 otherwise a conflict will be detected by the configuration
                 program.
        "

;==============================================================================

NamedItem

Prompt  "Single Screen Mode"

choice  " EGA"  pos[0]=0XXXXXXXb
choice  " VGA"  pos[0]=1XXXXXXXb

Help    " 'EGA' is 640x350 A/N mode, 8x14 character cell.
          'VGA' is 720x400 A/N mode, 9x16 character cell.
        "

;==============================================================================

NamedItem

Prompt  "Video Sync Mode"

choice  " PIN 4=CSYNC, PIN 5=5v"    pos[1]=X1XXXX1Xb
choice  " PIN 4=HSYNC, PIN 5=VSYNC" pos[1]=X0XXXX0Xb

Help    " Selects the synchronization mode required by the monitor
          connected to the video output of the PG2-1281. There are
          two different modes:

          'pin 4 = HSYNC pin 5 = VSYNC' places horizontal sync and
           vertical sync on pins 4 and 5 of the output video
           connector respectively.

          'pin 4 = CSYNC pin 5 = 5v' places composite sync and 5
           volts on pins 4 and 5 of the output video connector
           respectively.
        "

;==============================================================================

NamedItem

Prompt  "Sync on Video"

choice  " ON "  pos[1]=0XXXXXX0b
choice  " OFF"  pos[1]=1XXXXXX1b

Help    " 'ON' enables Sync on video,
          'OFF' disables Sync on video.
        "

;==============================================================================

NamedItem

Prompt  "Interrupt"

choice  " IRQ7" pos[0]=XXX1XXXXb    int 7
choice  " IRQ5" pos[0]=XXX0XXXXb    int 5

Help    " 'IRQ7' assigns Interrupt level 7 for the PG2-1281.
          'IRQ5' assigns Interrupt level 5 for the PG2-1281.
        "