Good Morning.
I have and AlphaServer 1200 which was physically abused in transit. The
system boots to the console OK, and the test utility indicates the the
CPU's and memory are OK. I am trying to install TRU64 5.1A on the box
and get the following error during the CD boot:
(boot dka500.5.0.1.1 -flags A)
pblock 0 of dka500.5.0.1.1 is a valid boot block
reading 15 blocks from dka500.5.0.1.1
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
configuring I/O adapters...
ncr0, hose 1, bus 0, slot 1
isp0, hose 1, bus 0, slot 2
floppy0, hose 0, bus 1, slot 0
tulip0, hose 0, bus 0, slot 3
tulip1, hose 0, bus 0, slot 4
jumping to bootstrap code
UNIX boot - Wednesday August 01, 2001
Loading vmunix ...
Loading at 0xffffffff00000000
Sizes:
text = 7074304
data = 1718352
bss = 2258496
Starting at 0xffffffff000104c0
DUMP: A dump found in memory will tie up 2187264 bytes until released.
Alpha boot: available memory from 0x13ba000 to 0x2fffc000
Compaq Tru64 UNIX V5.1A (Rev. 1885); Wed Aug 1 15:16:14 EDT 2001
physical memory = 512.00 megabytes.
available memory = 488.31 megabytes.
using 636 buffers containing 4.96 megabytes of memory
Master cpu at slot 0
Firmware revision: 5.7
PALcode: UNIX version 1.23
AlphaServer 1200 5/533 4MB
pci1 (primary bus:1) at mcbus0 slot 5
Loading SIOP: script c0000000, reg 7feef00, data c000a000
scsi0 at psiop0 slot 0 rad 0
isp0 at pci1 slot 2
isp0: QLOGIC ISP1040B/V2
isp0: Firmware revision 5.57 (loaded by console)
isp0: Fast RAM timing enabled.
scsi1 at isp0 slot 0 rad 0
pci0 (primary bus:0) at mcbus0 slot 4
eisa0 at pci0
s3trio0: S3 Trio64V+ (SVGA) Plug-N-Play, 1.0 Mb
s3trio0 at pci0 slot 2
tu0: DECchip 21143: Revision: 3.0
tu0: auto negotiation capable device
tu0 at pci0 slot 3
tu0: DEC TULIP (10/100) Ethernet Interface, hardware address:
00-00-F8-10-90-D5
tu0: auto negotiation off: selecting 100BaseTX (UTP) port: half duplex
tu1: DECchip 21143: Revision: 3.0
tu1: auto negotiation capable device
tu1 at pci0 slot 4
tu1: DEC TULIP (10/100) Ethernet Interface, hardware address:
00-00-F8-10-91-75
tu1: auto negotiation off: selecting 100BaseTX (UTP) port: half duplex
Created FRU table binary error log packet
configure_console: No serial driver from get_info
No kernel console driver installed
NetRAIN configured.
i2c: Server Management Hardware Present
Warning: No time set in file system, using the system clock.
This date may not be correct, please check it after booting
vm_swap_init: warning UNSPECIFIED swap device not found
vm_swap_init: swap is re-set to lazy (over commitment) mode
panic (cpu 0): System does not have a console configured.
syncing disks... done
DUMP: Warning: no disk available for dump.
DUMP: first crash dump failed: attempting memory dump...
DUMP: compressing 36416KB into 460143KB memory...
DUMP: Starting Address Ending Address Size(MB)
DUMP: ------------------ ------------------ --------
DUMP: 0xfffffc0002a7fc00 - 0xfffffc000fffffef 213.5 (indicator)
DUMP: 0xfffffc002fc7c000 - 0xfffffc002fffbfef 3.5 (indicator)
DUMP: Writing data.. [2MB]
DUMP: crash dump complete.
halted CPU 0
The key message (I think) is "panic (cpu 0): System does not have a
console configured.
"
The console environment variables are:
P00>>>sho *
auto_action RESTART
boot_dev dkb0.0.0.2.1
boot_file
boot_osflags A
boot_reset ON
bootdef_dev dkb0.0.0.2.1
booted_dev
booted_file
booted_osflags
cda0 dka500.5.0.1.1
CDA1 dka500.5.0.1.1
CDA2 dka500.5.0.1.1
CDA3 dka500.5.0.1.1
CDA4 dka500.5.0.1.1
char_set 0
com1_baud 9600
com1_flow SOFTWARE
com1_modem OFF
com2_baud 9600
com2_flow SOFTWARE
com2_modem OFF
console serial
cpu_enabled f
d_group field
d_omit
d_passes 1
d_runtime 0
d_verbose 0
dump_dev
enable_audit ON
ewa0_loop_count 3e8
ewa0_loop_inc a
ewa0_loop_patt ffffffff
ewa0_loop_size 2e
ewa0_lp_msg_node 1
ewa0_mode Fast
ewb0_loop_count 3e8
ewb0_loop_inc a
ewb0_loop_patt ffffffff
ewb0_loop_size 2e
ewb0_lp_msg_node 1
ewb0_mode Fast
exdep_data 5555555555555555
exdep_location 0
exdep_size 0
exdep_space pmem
exdep_type 3
ffauto OFF
ffnext OFF
fru_table ON
full_powerup_diags ON
graphics_page 0
graphics_type VIDEO
kbd_hardware_type PCXAL
language 36
language_name English (American)
license MU
memory_test full
ocp_text AS-1200-01
os_type UNIX
pal OpenVMS PALcode V1.21-2, Digital UNIX PALcode
V1.23-2
pci_arbmode Round-Robin
pci_parity ON
pci_req64
pka0_disconnect 1
pka0_fast 1
pka0_host_id 7
pkb0_disconnect 1
pkb0_fast 1
pkb0_host_id 7
pkb0_soft_term on
pkc0_disconnect 1
pkc0_fast 1
pkc0_host_id 7
prompt >>>
rcm_answer ATXA
rcm_dialout
rcm_init AT&F0EVS0=0S12=50
reset_boot_arg0 0
reset_boot_arg1
reset_boot_arg2
shutdown_temp 55
srm2dev
sys_model_num 1200
sys_serial_num NI83806704
sys_type PEDESTAL
sys_variant 0
tga_sync_green 0
tt_allow_login 1
tta0_page 0
tta0_type VIDEO
tty_dev 0
version V5.7-4, 27-MAR-2000 09:52:35
I am connecting through the serial port via terminal emulator on my
laptop. Does anyone know what the above error means and how to correct
it?
TIA
Ralf Borowski
rborowski_at_tembec.ca
Received on Tue Mar 19 2002 - 16:12:57 NZST